thats sort of what i was thinking . might give it a try out and see if its any good

there is no part number bud . just a picture . listings on e bay . https://www.ebay.co.uk/itm/Water-Pump-Oil-Seal-SET-for-HONDA-CRM250-CRF450X-Free-shipping/122984169125?_trkparms=pageci%3A814d6846-2d44-11e8-92b6-74dbd18080ba%7Cparentrq%3A4a3324831620abd8d486b0affff7b0da%7Ciid%3A1&_trksid=p2481888.c...

have been looking for the waterpump mechanical seal formy crm . e bay prices very from cheap to holy poo prices but the sellers in japan lol . noticed someone selling a seal for £26 but in the description it says this seal fits the crf 450x as well . so is the crm 250 mechanical seal the same as the...

yup there fubard . hairline cracks and a chunk missing .

just started my second rebuild of my mk2 crm . the swingarm bearing bushes are cracked and i cant seem to find anyone that stocks these . its driving me round the twist . bought the all balls kit for the XR and the bushes dont fit . my pin is 15mm outside diameter . any one know where i can get thes...

Hi mate . sounds like its both forks . TBH i dont think my forks had been serviced at all . when i drained the old oil out there wasnt much in there and it was black . the new oil i put in was much thinner than the oil that came out . i have been out on the bike last weekend doing a bit of bing bash...

evening . rebuilt my front shocks a few weeks back on my mk2 . replaced the bushes , oil seal and dust seals and got some lovely clean fork oil to stick in . shocks are back on the bike but i now get a noise that sounds like the springs are rubbing inside the fork legs and also a slight clicking noi...

if your pv servo is spining its usually a broken wire or a dirty connection in the servo wire plug that connects to the loom . potentiometer could also be in need of a clean with electrical cleaner . dont use WD40 as this waxes up the carbon tipped contact inside the unit

Hi, sorry mate, but could you run another compression test on it now she's new? I think mines a bit down, I got about 82psi, I'm aware two strokes run lower compression than a four stroke anyway, but my TTR 265 is pushing out about 135-140PSI, and the revs are hanging a bit when I rev it up in neut...

happy days . put the old girl back together today . spent most of the day doing it as i tend to get a bit hashy when i power on so took plenty of time . only problem was the power valve flap . the guy who done my rebore said he had it in place whilst doing the work and there were no issues of it fow...

just found this on E bay . is it just me or does this look like its past its best but made to look nice with some silver paint . guy says its rare to find these in such good condition but the bore looks like its cracked above the exhaust port and the cylinder head gasket face dont look good http://w...

FFs lads im scottish . head gasket is fine . had a few MX bikes and done this trick everytime with no problems lol

I rebuilt the engine october 2014 and the bike wasnt really used until may 2015 . used honda seals as i am a bit OCD when it comes to stuff like this . i would hope i would get more life out of genuine honda parts , all the same you never can tell when any engine part might fail lol . got my barrel ...

hi knackered , yeah bikes been A1 . total rebuild a year and a half ago with new crank seals etc . checked the rubber inlet connector and thats fine . split the carb and both jets are clean and the carb bowl is clean . think its the mixture screw o ring . would a worn o ring cause such a change to t...

Hi chaps . was out last sunday with the hillbillys doing some woods enduro and a bit of bing bashing . bike was running really well but the last hour she started running lean . revs were hanging on a bit when i revved the bike . tried adjusting the air screw etc and noticed it turned very easily , s...