Rear Linkage bearings
- jonnygal
- New kid on the block
- Reactions:
- Posts: 48
- Joined: 19 May 2016, 22:35
- Bike Owned: 250 mk2
- Location: west yorkshire
Rear Linkage bearings
Hi
I have a 1992 mk2 and currently have the shocker off for full refurb and want to get all the bearings and seals changed in the linkages.
I have looked at the F & Q section where I got some good info on this, just got one question. Where is the best place to buy a full set of rear linkage bearings and seals.
Thanks for your help
Jon
I have a 1992 mk2 and currently have the shocker off for full refurb and want to get all the bearings and seals changed in the linkages.
I have looked at the F & Q section where I got some good info on this, just got one question. Where is the best place to buy a full set of rear linkage bearings and seals.
Thanks for your help
Jon
Re: Rear Linkage bearings
Personally I find it easier to give leisure trail a call , some people say they're pricey but I think they're a lot more competitive than they were and Tom in the parts dept is a star .jonnygal wrote:Hi
I have a 1992 mk2 and currently have the shocker off for full refurb and want to get all the bearings and seals changed in the linkages.
I have looked at the F & Q section where I got some good info on this, just got one question. Where is the best place to buy a full set of rear linkage bearings and seals.
Thanks for your help
Jon
There's a lot of info on here about alternative places for parts and what parts from other models fit the CRM
- jonnygal
- New kid on the block
- Reactions:
- Posts: 48
- Joined: 19 May 2016, 22:35
- Bike Owned: 250 mk2
- Location: west yorkshire
Re: Rear Linkage bearings
Thanks pal, have seen they do the wheel bearings I need after someone pointed me in the right direction to leisure trial , I will call tmrw and ask they do.jompy wrote:Personally I find it easier to give leisure trail a call , some people say they're pricey but I think they're a lot more competitive than they were and Tom in the parts dept is a star .jonnygal wrote:Hi
I have a 1992 mk2 and currently have the shocker off for full refurb and want to get all the bearings and seals changed in the linkages.
I have looked at the F & Q section where I got some good info on this, just got one question. Where is the best place to buy a full set of rear linkage bearings and seals.
Thanks for your help
Jon
There's a lot of info on here about alternative places for parts and what parts from other models fit the CRM
Thanks again.
Sent from my iPad using Tapatalk
Re: Rear Linkage bearings
Leisure trail is less than 10 miles from mejonnygal wrote:Thanks pal, have seen they do the wheel bearings I need after someone pointed me in the right direction to leisure trial , I will call tmrw and ask they do.jompy wrote:Personally I find it easier to give leisure trail a call , some people say they're pricey but I think they're a lot more competitive than they were and Tom in the parts dept is a star .jonnygal wrote:Hi
I have a 1992 mk2 and currently have the shocker off for full refurb and want to get all the bearings and seals changed in the linkages.
I have looked at the F & Q section where I got some good info on this, just got one question. Where is the best place to buy a full set of rear linkage bearings and seals.
Thanks for your help
Jon
There's a lot of info on here about alternative places for parts and what parts from other models fit the CRM
Thanks again.
Sent from my iPad using Tapatalk

-
- NWAA Supporter
- Reactions:
- Posts: 3520
- Joined: 02 Dec 2007, 16:02
- Bike Owned: MK3
- Location: Mid Surrey
Re: Rear Linkage bearings
You can get all the bearings from a bearing factor shop like Simply bearings,but you'll have to measure yours first for the correct sizes.
On the linkage bearings, they come out slightly longer, which in a way is good, as gives more bearing surface, additionally they have two seals built into the bearing as well,which helps if the crud gets past the first seal.
Mike
On the linkage bearings, they come out slightly longer, which in a way is good, as gives more bearing surface, additionally they have two seals built into the bearing as well,which helps if the crud gets past the first seal.
Mike
VFORCE REEDS-MUGEN HEAD AND BARREL-WHITE POWER-ALL ON MY WISH LIST!!
- jonnygal
- New kid on the block
- Reactions:
- Posts: 48
- Joined: 19 May 2016, 22:35
- Bike Owned: 250 mk2
- Location: west yorkshire
Re: Rear Linkage bearings
Excellentfallenmikethebike wrote:You can get all the bearings from a bearing factor shop like Simply bearings,but you'll have to measure yours first for the correct sizes.
On the linkage bearings, they come out slightly longer, which in a way is good, as gives more bearing surface, additionally they have two seals built into the bearing as well,which helps if the crud gets past the first seal.
Mike
Thanks for that, I will get it stripped and measure the bearings.
Sent from my iPhone using Tapatalk
- jonnygal
- New kid on the block
- Reactions:
- Posts: 48
- Joined: 19 May 2016, 22:35
- Bike Owned: 250 mk2
- Location: west yorkshire
Re: Rear Linkage bearings
Leisure trail sorted me out yesterday, order the rear wheel bearings and seals at 5pm and they turned up this morning
SERVICE!
Sent from my iPhone using Tapatalk

Sent from my iPhone using Tapatalk
Re: Rear Linkage bearings
Nice one bud , chuffed for youjonnygal wrote:Leisure trail sorted me out yesterday, order the rear wheel bearings and seals at 5pm and they turned up this morningSERVICE!
Sent from my iPhone using Tapatalk